Ch 1 · Solutions Start
Chemistry · Ch 1 · Topic 8 of 12 · 9 slides

Part E · Colligative Properties

Solutions

Swipe left or right to change slide

Part E · Colligative Properties

Four properties depend only on the number of solute particles: (1) relative lowering of vapour pressure, (2) elevation of boiling point, (3) depression of freezing point, (4) osmotic pressure.

Part E · Colligative Properties
QuantityFormulaUnit
Relative lowering of v.p.
–
Elevation of boiling point
K
Depression of freezing point
K
Molar mass from ΔT
g mol−1
Osmotic pressure
bar / atm
Molar mass from π
g mol−1
Part E · Colligative Properties

Difficult word → Why does a solute raise the boiling point and lower the freezing point?

The solute lowers the vapour pressure. To boil, the vapour pressure must reach 1 atm – so the solution must be heated to a higher temperature. At the freezing point, solid and liquid must have the same vapour pressure – the solution's lower vapour pressure meets the solid's curve at a lower temperature.

Hinglish mein samjho: Vapour pressure kam hua → ubalne ke liye zyada garam karna padega, jamne ke liye zyada thanda.
Part E · Colligative Properties

SOLVED NUMERICAL – Molar mass from relative lowering of vapour pressure

Step 1: Pure benzene p° = 0.850 bar; 0.5 g solute in 39 g benzene (M = 78) gives p = 0.845 bar.

Step 2: Use the formula and solve for M2:

Answer: M2 = 170 g mol−1

Part E · Colligative Properties

SOLVED NUMERICAL – Boiling point of glucose solution

Step 1: 18 g glucose (M = 180) in 1 kg water → molality:

Step 2: ΔTb = Kb × m:

Step 3: New boiling point:

Answer: 373.202 K

Part E · Colligative Properties

SOLVED NUMERICAL – Freezing point of an antifreeze solution

Step 1: 45 g ethylene glycol (M = 62) in 600 g water:

Step 2: ΔTf = Kf × m:

Step 3: Freezing point:

Answer: 270.9 K

Part E · Colligative Properties

Osmosis and osmotic pressure

  • Semipermeable membrane (SPM): lets solvent pass but not solute (e.g. animal bladder, cellophane, parchment).
  • Osmotic pressure (π): the extra pressure that must be applied on the solution side to stop osmosis.
  • π is the best method for molar masses of proteins / polymers – measured at room temperature and gives large values even for dilute solutions.
  • Isotonic: same π (0.9% NaCl = normal saline with blood). Hypertonic (more concentrated) → cells shrink; hypotonic → cells swell and burst.
  • Reverse osmosis: apply pressure greater than π → pure water is pushed out of the solution. Used in desalination of sea water (cellulose acetate membrane).
Hinglish mein samjho: Osmosis mein paani patle se gaadhe ki taraf. Ulta dabaav π se zyada lagao to paani bahar – yahi RO water purifier.
Part E · Colligative Properties

SOLVED NUMERICAL – Molar mass of a protein from osmotic pressure

Step 1: 1.26 g protein in 200 cm3 solution has π = 2.57 × 10−3 bar at 300 K. V = 0.200 L, R = 0.083 L bar K−1 mol−1.

Step 2: Use M2 = w2RT / (πV):

Answer: ≈ 61 022 g mol−1

Part E · Colligative Properties

Quick check

Colligative properties depend on:

Practice only – this does not count as a test.

✓

Topic 8 done!

Log in to save your progress.